The following commands are specific to the ras IP context within the Netsh environment.
To view the command syntax, click a command:
Add commands
Delete commands
Set commands
- set access
- set addrassign
- set addrreq
- set broadcastnameresolution
- set negotiation
- set preferredadapter
Show commands
Netsh commands for ras IP
- The following entries provide details for each command.
dump
Displays the IP configuration of a remote access server in script form.
Syntax
dump
Remarks
- You can dump the contents of the current configuration to a
file that can be used to restore altered configuration
settings.
Example
Following is the command to save the current configuration as a script in the rasipcfg.dmp file.
dump > rasipcfg.dmp
show config
Displays the current IP configuration of the remote access server.
Syntax
show config
set negotiation
Specifies whether the remote access server should allow IP to be configured for any client connections the server accepts.
Syntax
set negotiation
[mode=] {allow | deny}
Parameters
- [mode=] {allow | deny}
- Required. Specifies whether to permit IP over client connections. The allow parameter allows IP over client connections. The deny parameter prevents IP over client connections.
set access
Specifies whether IP network traffic from any client should be forwarded to the network or networks to which the remote access server is connected.
Syntax
set access
[mode=] {all | serveronly}
Parameters
- [mode=] {all | serveronly}
- Required. Specifies whether clients should be able to reach the remote access server and any networks to which it is connected. The all parameter allows clients to reach networks through the server. The serveronly parameter allows clients to reach only the server.
set addrassign
Sets the method by which the remote access server should assign IP addresses to its clients.
Syntax
set addrassign
[method=] {auto | pool}
Parameters
- [method=] {auto | pool}
- Required. Specifies whether IP addresses should be assigned by using DHCP or from a pool of addresses held by the remote access server. The auto parameter specifies that addresses should be assigned by using DHCP. If no DHCP server is available, a random, private address is assigned. The pool parameter specifies that addresses should be assigned from a pool.
set addrreq
Specifies whether dial-in clients should be able to request their own IP addresses.
Syntax
set addrreq
[mode=] {allow | deny}
Parameters
- [mode=] {allow | deny}
- Required. Specifies whether clients should be able to request their own IP addresses. The allow parameter allows clients to request addresses. The deny parameter prevents clients from requesting addresses.
set broadcastnameresolution
Enables or disables broadcast name resolution using NetBIOS over TCP/IP.
Syntax
set broadcastnameresolution
[mode=] {enabled | disabled}
Parameters
- [mode=] {enabled | disabled}
- Required. Specifies whether to enable or disable broadcast name resolution using NetBIOS over TCP/IP. The enabled parameter enables broadcast name resolution using NetBIOS over TCP/IP. The disabled parameter disables broadcast name resolution using NetBIOS over TCP/IP.
Remarks
- To check the status of broadcastnameresolution, use the
dump command.
show broadcastnameresolution
Displays whether broadcast name resolution using NetBIOS over TCP/IP has been enabled or disabled for the remote access server.
Syntax
show broadcastnameresolution
add range
Adds a range of addresses to the pool of static IP addresses that the remote access server can assign to clients.
Syntax
add range
[from=] StartingIPAddress
[to=] EndingIPAddress
Parameters
- [from=] StartingIPAddress [to=] EndingIPAddress
- Required. Specifies the range of IP addresses to add. The StartingIPAddress parameter specifies the first IP address in the range. The EndingIPAddress parameter specifies the last IP address in the range.
Example
To add the range of IP addresses 10.2.2.10 to 10.2.2.20 to the static pool of IP addresses that the remote access server can assign, type:
add range from=10.2.2.10 to=10.2.2.20
delete range
Deletes a range of addresses from the pool of static IP addresses that the remote access server can assign to clients.
Syntax
delete range
[from=] StartingIPAddress
[to=] EndingIPAddress
Parameters
- [from=] StartingIPAddress [to=] EndingIPAddress
- Required. Specifies the range of IP addresses to delete. The StartingIPAddress parameter specifies the first IP address in the range. The EndingIPAddress parameter specifies the last IP address in the range.
Example
To delete the range of IP addresses 10.2.2.10 to 10.2.2.20 from the pool of static IP addresses that the remote access server can assign, type:
delete range from=10.2.2.10 to=10.2.2.20
delete pool
Deletes all addresses from the pool of static IP addresses that the remote access server can assign to clients.
Syntax
delete pool
set preferredadapter
Specifies the preferred adapter for Routing and Remote Access service.
Syntax
set preferredadapter
[name=] InterfaceName
Parameters
- [name=] InterfaceName
- Specifies that the adapter to be used to obtain the IP addresses for allocation (if configured to use DHCP) and the IP address of DHCP and WINS servers for assignment to remote access clients and demand-dial routers. If no interface is specified, the server randomly selects an adapter when the Routing and Remote Access service is started.
show preferredadapter
Displays the preferred adapter for Routing and Remote Access service.
Syntax
show preferredadapter